Deadbolt Installation in Farmington, NM — Stronger Doors, Better Security
Builder-grade deadbolts on most Farmington homes are the weakest point in the door — and a proper deadbolt upgrade is the fastest way to fix that. We install Grade 1 and Grade 2 deadbolts, smart locks, and high-security cylinders for homes and businesses across Farmington and San Juan County — priced on the phone before we start.
Deadbolt Installation Farmington NM — Residential & Commercial Services
Our deadbolt installation Farmington NM service covers replacement, upgrade, and new installs for homes and businesses across Farmington and San Juan County. Whether it’s a standard single-cylinder deadbolt on a front door or a high-security grade 1 lock on a commercial entry, we supply the hardware or install hardware you’ve already purchased.
Single Cylinder Deadbolt
Standard keyed entry from outside, thumb turn from inside. The most common residential deadbolt — installed on most front and back doors.
Double Cylinder Deadbolt
Keyed entry from both sides — no thumb turn. Used on doors with glass panels or sidelights where the thumb turn could be reached through broken glass.
Smart Lock Installation
Keypad, app-controlled, and push-to-start smart locks installed and configured. We handle both the physical installation and the initial setup.
High-Security Deadbolts
Grade 1 commercial-grade deadbolts with anti-pick, anti-drill, and anti-bump protection for high-traffic or high-risk entry points.
Deadbolt Installation Cost in Farmington NM — What Determines the Price
For deadbolt installation Farmington NM homeowners and businesses, cost depends on three things: the type of deadbolt, whether it’s a replacement or a new installation, and whether you supply the hardware or want us to. We quote a flat price on the phone before we head out.
Single Cylinder Deadbolt — Installed
Labour plus hardware for a standard Grade 1 or Grade 2 single cylinder deadbolt replacing an existing lock. The most common job — most Farmington homes have the standard 2⅛” bore already drilled, so it’s a direct swap. Takes 15–30 minutes per door.
If you supply the hardware yourself, labour only runs $50–$100. Buying your own lock and bringing it to the appointment can save 20–30% on hardware markup.
Double Cylinder Deadbolt — Installed
Keyed entry from both sides — used on doors with glass panels where a thumb turn could be reached through broken glass. Takes slightly longer to install than a single cylinder. Note: double cylinders require a key to exit in an emergency — we’ll discuss the fire safety trade-off before installing one.
Most residential building codes allow double cylinders; some jurisdictions restrict them. We’ll confirm what applies to your Farmington property before recommending one.
Smart Lock — Installed & Configured
Smart lock installation includes the physical deadbolt swap plus initial setup: Wi-Fi or Bluetooth pairing, access code configuration, and connectivity testing. Hardware cost varies significantly by brand — Schlage Encode, Kwikset Halo, Yale Assure, August Smart Lock each have different price points.
Call with the brand and model you want — we’ll confirm compatibility with your door and what the full installed cost looks like before scheduling.
Deadbolt Installation Farmington NM — Why Most Homes Need an Upgrade
Most homes built in Farmington in the last two decades came with Grade 3 builder-grade deadbolts — the minimum hardware required by building code, not the best available. In a market with significant rental housing serving the San Juan Basin workforce, many properties have seen multiple tenants and years of wear on the same hardware.
A deadbolt installation Farmington NM upgrade to Grade 1 or Grade 2 hardware takes 20–30 minutes per door and provides a meaningful improvement in forced-entry resistance. The most common reasons Farmington homeowners call us for a deadbolt upgrade:
New purchase or rental move-in — rekey and upgrade the existing deadbolts at the same time so you start with hardware you trust.
If a door was forced or kicked in, the hardware and frame both need assessment. We check the strike plate and door frame as part of every post-break-in deadbolt installation.
A deadbolt that’s hard to throw, won’t latch cleanly, or has visible wear on the cylinder is overdue for replacement. A failing lock is not just an inconvenience — it’s a security risk.
Remote access, keypad entry, and access logs make smart lock deadbolts practical for rental properties, home-based businesses, and households managing multiple keyholders.
Interior garage entry doors and secondary exterior doors often have only a knob lock — no deadbolt. We drill the new bore and install a proper deadbolt on the same visit.
The Part of Your Door That Matters More Than the Deadbolt
Most forced entries don’t defeat the deadbolt — they split the door frame at the strike plate. Standard builder-grade strike plates use short ¾” screws that only go into the door stop, not the structural stud behind it. One solid kick can split the frame regardless of how strong the deadbolt is.
Every deadbolt installation Farmington NM job we do includes a strike plate check. If the existing plate uses short screws or is poorly positioned, we install a reinforced strike plate with 3″ screws that anchor into the door stud — or recommend a full door frame reinforcement kit for doors that see heavy use or are in higher-risk locations.
This is the single highest-impact upgrade available for most residential doors in Farmington. If your deadbolt is Grade 1 but your strike plate is still builder-grade, the Grade 1 lock isn’t doing what you think it is.
Supply your own hardware or we can bring it — tell us when you call.
Deadbolt Grades Explained — What the Ratings Actually Mean
Deadbolts are rated by ANSI/BHMA grades — Grade 1 being the highest and Grade 3 the lowest. Most builder-grade deadbolts installed in Farmington homes are Grade 3 — the cheapest hardware that meets minimum building code. Here’s what each grade actually offers.
Highest Security
Tested to withstand 250,000 open/close cycles and a 360 lb. strike force. Anti-pick pins, hardened steel bolt, reinforced strike plate. Standard on commercial doors and recommended for any high-risk residential entry — front doors, basement entries, garage-to-house doors.
Brands: Schlage B60N, Kwikset 980, Medeco, Mul-T-Lock. We supply and install all of these on request.
Mid-Range Security
Tested to 150,000 cycles and a 250 lb. strike. Stronger than builder-grade but without the full pick and drill resistance of Grade 1. A reasonable upgrade for interior doors, secondary entries, and rental properties where Grade 1 isn’t required.
This is the sweet spot for most Farmington homeowners who want something better than builder-grade without the cost of a full commercial-grade installation.
Minimum Standard
Tested to 250,000 cycles on a lower strike force standard. The lock you’ll find on most new construction and rental properties in Farmington. Adequate for interior doors and low-risk entries — not recommended as the primary lock on an exterior door where security matters.
If your home was built in the last decade and you haven’t upgraded the deadbolts, there’s a good chance Grade 3 hardware is what’s protecting your exterior doors.
Deadbolt Installation Farmington NM — What’s Involved
Most deadbolt installations are straightforward — if there’s an existing hole in the door, it’s a direct swap. Here’s what each scenario involves.
Replacing an Existing Deadbolt
The most common job. The existing hole in the door accepts a standard 2⅛” bore — most deadbolts use this size, so replacement is a direct swap. We remove the old hardware, install the new deadbolt, check alignment with the strike plate, and test the bolt throw. Takes 15–30 minutes per door.
If the existing strike plate is builder-grade or uses short screws, we replace it with a reinforced strike plate and 3″ screws as part of the installation — the strike plate is where most forced-entry attacks succeed, not the deadbolt itself.
New Deadbolt on an Existing Door
Adding a deadbolt to a door that doesn’t currently have one requires boring a new hole through the door and the door frame. We assess the door material and thickness first — solid wood, hollow core, fiberglass, and steel doors each have different considerations. We bring the right bits and tools for each.
We also verify the frame can support a proper strike plate installation — a solid deadbolt on a weak frame is only as strong as the frame.
Smart Lock Installation
Most smart locks are designed to fit a standard single-cylinder deadbolt hole — the physical installation is usually the same as a standard deadbolt swap. The additional step is setup: connecting the lock to Wi-Fi or Bluetooth, configuring access codes, and testing connectivity.
We handle installation and initial setup. Call with the brand and model you have or want — we’ll confirm compatibility with your door and what’s involved before scheduling.
Door Frame & Strike Plate Reinforcement
The weakest point in most residential doors isn’t the deadbolt — it’s the strike plate and the wood around it. Standard builder-grade strike plates use ¾” screws into a thin wood door stop. A single kick can split the frame regardless of how strong the deadbolt is.
We install reinforced strike plates with 3″ screws that reach into the door stud, or full door frame reinforcement kits for maximum kick resistance. This is the highest-impact security upgrade available for most residential doors — often more effective than upgrading the deadbolt alone.
How to Book Deadbolt Installation in Farmington NM
Simple and straightforward from first call to installed hardware.
Call With Your Door Details
Tell us what you need — a replacement, a new installation, or a smart lock setup — and where you are in Farmington or San Juan County. If you already have the hardware, tell us the brand and model. If you need us to supply it, tell us the door type and what grade you want. We’ll quote a price on the phone and confirm availability.
We Come to You
We arrive with the tools and hardware needed for your job. For replacement jobs, we bring a selection of Grade 1 and Grade 2 deadbolts in common finishes. For new installations, we assess the door on site before drilling anything and confirm the plan with you first.
Installed, Tested, Done
We install the deadbolt, verify alignment, test the bolt throw and key operation, and check the strike plate. The price you heard on the phone is what you pay. If we find a door frame issue that needs addressing, we tell you and wait for your go-ahead before doing anything extra.
Frequently Asked Questions
Don’t see your question? Give us a call and we’ll answer it directly.
Deadbolt Installation Across Farmington & San Juan County
When you need deadbolt installation Farmington NM homeowners and businesses rely on, we come to your property across Farmington and the surrounding area. Most jobs in Farmington proper are scheduled same day or next day. For Aztec, Bloomfield, and outlying areas, call and ask — we cover most of San Juan County.
Not sure if we cover your location? Call and ask — we’ll give you a straight answer.
For lock rekeying see our lock rekey service in Farmington. For residential lock services see our residential locksmith page. For commercial lock work see our commercial locksmith services.
Need Reliable Deadbolt Installation in Farmington NM?
Call us — we’ll quote on the phone, supply hardware if needed, and install same day for most jobs in Farmington.